Product ID:ADHESIVE LCA-4
MSDS Date:10/24/1989
FSC:8040
NIIN:00-133-4391
MSDS Number: BJYRG

BACON INDUSTRIES INC.

192 PLEASANT STREET
WATERTOWN, MA 02172
US

Emergency Phone: 617-926-2550/714-863-1499/BUS HOURS

Info Phone: 508-668-6753/714-559-1134/NTS-WKEND

Cage: 99098

BACON INDUSTRIES, INC.

WATERTOWN, MA 02172 US

Telephone: 617-926-2550

Cage: 99098

4,4'-(1-METHYLETHYLIDENE) BISPHENOL POLYMER WITH

CAS: 25068-38-6

RTECS: KD4380000

Fraction By Weight: 30%

CALCIUM CARBONATE (MARBLE) (LIMESTONE)

CAS: 1317-65-3

RTECS: EV9580000

Fraction By Weight: 60%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9192

SILICA (MATERIALS IN NON-AIRBORNE FORM)

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 2%

OSHA PEL 20 MPPCF

LD50 LC50 Mixture:ORAL RAT LD50 11.4G/KG;LD50 RABB 20ML/KG
Health Hazards Acute and Chronic:INGESTION: SINGLE ORAL DOSE TOXICITY
IS LOW. INHALATION: AT AMBIENT CONDITIONS, VAPORS ARE UNLIKELY TO
CAUSE HARM. MODERATE HEATING CAN GENERATE VAPORS THAT COULD CAUSE
RESPIRATORY IRRITATION IF INHAL ED. SKIN: MAY CAUSE ALLERGIC SKIN
REACTION (REDDENING AND SWELLING). SENSITIZER-MAY CAUSE ALLERGIC
REACTION IN CERTAIN
Explanation of Carcinogenicity:A TEST OF QUESTIONABLE VALIDITY SHOW
EPOXY RESIN CAUSING SKIN CANCER IN MICE.
Effects of Overexposure:INDIVIDUALS. PROLONGED EXPOSURE IS NOT LIKELY
TO CAUSE SIGNIFICANT SKIN IRRITATION ALTHOUGH REPEATED EXPOSURE
MAY. FOR SKIN ABSORPTION, A SINGLE DOSE IS NOT LIKELY TO BE
ABSORBED THROUGH THE SKIN IN H ARMFUL AMOUNTS. EYE: MAY CAUSE
SLIGHT TEMPORARY EYE IRRITATION. CORNEAL INJURY IS UNLIKELY.

First Aid:EYE CONTACT: IMMEDIATELY FLUSH W/LARGE AMOUNTS WATER FOR AT
LEAST 10 MINUTES. CONTACT PHYSICIAN IMMEDIATELY. SKIN CONTACT: WIPE
OFF EXCESS WITH TOWEL AND IMMEDIATELY WASH THOROUGHLY WITH SOAP AND
WATE R. INHALATION: MOVE TO FRESH AIR IF SYMPTOMS OCCUR. CONSULT
PHYSICIAN. INGESTION: CALL A PHYSICIAN OR POISON CONTROL CENTER
IMMEDIATELY. NO SPECIFIC ANTIDOTE. TREATMENT BASED ON PHYSICIAN'S
JUDGMENT.

Flash Point Method:PMCC
Flash Point:480F,249C
Extinguishing Media:WATER SPRAY, CARBON DIOXIDE, FOAM OR DRY CHEMICAL.
Fire Fighting Procedures:WEAR POSITIVE SELF-CONTAINED BREATHING
APPARATUS AND FULL PROTECTIVE CLOTHING. AVOID BREATHING SMOKE.
Unusual Fire/Explosion Hazard:KEEP NON-IGNITED MATERIAL COOL W/WATER
SPRAY.BEWARE OF POSSIBLE EXOTHERMIC REACTION IF MAT'L IS HEATED
>400 F IN A CONTAINER CONTAINING GREATER THAN 1 LB MAT'L.

Spill Release Procedures:REMOVE IGNITE SOURCES. WEAR PROTECTIVE
BREATHING APPARATUS/EQUIPMENT. LG SPILLS: DIKE & PUMP INTO
APPROPRIATE CONTAINERS. SMALL SPILLS: SOAK IN INERT ABSORB MAT'L.
REMOVE RESIDUAL RESIN W/HOT SOAPY WA TER. PLACE WASTE IN APPR'D
METAL CONTAINER & SEAL.

Handling and Storage Precautions:STORE AT 85 F OR BELOW.
Other Precautions:OBEY ALL OTHER RELEVANT LOCAL, STATE AND FEDERAL
LAWS. DO NOT CONTAMINATE LAKES, STREAMS, PONDS OR UNDERGROUND WATER
SUPPLIES.

Respiratory Protection:GOOD GENERAL VENTILATION SHOULD BE SUFFICIENT
FOR MOST CONDITIONS. IF HEATED MORE STRINGENT LOCAL VENTILATION MAY
BE PRUDENT.
Ventilation:VENT CURING OVENS OUTDOORS.
Protective Gloves:IMPERVIOUS LATEX OR RUBBER GLOVES.
Eye Protection:SAFETY GLASSES OR GOGGLES.
Other Protective Equipment:FOR BRIEF CONTACT, NO SPECIAL PRECAUTIONS
OTHER THAN CLEAN BODY-COVERING CLOTHING SHOULD BE NEEDED.
Work Hygienic Practices:CLOTHING CONTAMINATED WITH THIS MATERIAL SHOULD
BE WASHED BEFORE REUSING. DISCARD SEVERELY CONTAMINATED CLOTHING.
Supplemental Safety and Health
AVOID EYE & SKIN CONTACT. DO NOT WEAR CONTACT LENSES NEAR PRODUCT BEING
USED. CONTAINS MINERAL FILLERS IN A COMPLETELY WETTED, NON-AIRBORNE
FORM, SOME OF THESE COMPONENTS ARE CLASSIFIED AS HAZARDS. DO NOT
INHALE DUST IF CURED SUFACES ARE MACHINED, CUT, SANDED, ETC WHERE
PARTICLES GO INTO THE AIR.

HCC:V7
Boiling Pt:B.P. Text:500F,260C
Vapor Pres:0.03 @ 77F
Vapor Density:>1
Spec Gravity:1.87
Viscosity:PASTE
Evaporation Rate & Reference:NIL
Solubility in Water:NIL
Appearance and Odor:WHITE LIQUID PASTE, VERY SLIGHT ETHER ODOR.
Percent Volatiles by Volume:0%

Stability Indicator/Materials to Avoid:YES
UNCONTROLLED EXPOSURE TO STRONG OXIDIZING AGENTS, ACIDS, MERCAPTANS,
BASES OR AMINES, ESPECIALLY IN OVER 1 LB. MASSES.
Stability Condition to Avoid:EXCESSIVE HEAT OVER LONG PERIODS OF TIME
WILL DEGRADE THE RESIN.
Hazardous Decomposition Products:NITROGEN OXIDES, CARBON DIOXIDE,
CARBON MONOXIDE, ALDEHYDES AND OTHER HAZARDOUS ORGANICS.
Conditions to Avoid Polymerization:MAY OCCUR IF STORED AT ELEVATED
TEMPERATURE (>400 F) ESPECIALLY IN QUANTITIES GREATER THAN 1 LB.

Waste Disposal Methods:INCINERATION OF THE PRODUCT AT A U.S. EPA
PERMITTED WASTE FACILITY AND/OR BURIAL IN AN EPA SECURED LANDFILL.
OTHER APPLICABLE FEDERAL, STATE AND LOCAL REGULATIONS SHOULD ALSO
BE OBSERVED.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.